repair
Toro TimeMaster 30 blade belt replacement: what Toro says
Short answer
None of the seven operator’s manuals Toro linked for the TimeMaster 30 (21199, 21199HD and 21200) when we read them on 17 November 2026 prints a blade-drive belt part number, belt size or replacement procedure. All seven say to service the blade-drive system every 50 hours: remove its cover, clear out debris, slide a 0.25 mm (0.010 inch) feeler gauge or a piece of paper down behind the belt-tension spring, and, if there is a visible gap, tighten the adjusting bolt and nut until the paper barely slides freely. If the blades do not stop within 3 seconds of releasing the blade-control bar, they send you to an Authorized Service Dealer.
- Published
- Last verified
This guide is compiled from the manufacturer’s own documentation, cited below. We have not performed this procedure ourselves and do not claim to have.
Before you start
What you need
- A 0.25 mm (0.010 inch) feeler gauge, or a piece of paper or a note card
- A brush, or a way to blow out debris
- Gloves and eye protection
- For the blade-stop check: the empty grass bag, or a half sheet of newspaper and a paved surface
Procedure
Step by step
- 1
Prepare the machine before servicing the belt
Before any maintenance procedure, the manuals say to disconnect the spark-plug wire from the spark plug and remove the ignition key on the electric-start model (134599, which covers only the 21199HD, prints no key clause, and 185882 says “if equipped”). Wear gloves and eye protection. Manuals 171808, 172235 and 185882 also say to shut off the machine, wait for all moving parts to stop and let the machine cool before adjusting or servicing it.
The manuals say never to tamper with safety devices, and to check their proper operation regularly. - 2
Remove the blade-drive system cover and clean inside it
Remove the blade-drive system cover. The manuals’ drawing labels the cover and its bolts; they do not give the number of bolts or a tool size. Brush or blow out debris from the inside of the shield and around all the parts. The manuals list this service every 50 hours.
- 3
Check the belt-tension gap with a 0.25 mm (0.010 inch) gauge
Hold a 0.25 mm (0.010 inch) feeler gauge, a piece of paper or a note card against the wall and slide it down behind the belt-tension spring. If there is a visible gap between the gauge and the spring, tighten the adjusting bolt and the nut until the paper barely slides freely in and out of the gap. The manuals give the setting only as that feel: they state no tension force, no belt deflection and no torque for the bolt or nut.
Do not overtighten the adjusting bolt. The manuals warn that this could damage the blade-drive belt. - 4
Install the blade-drive system cover
Install the blade-drive system cover that you removed. That is the last step of the manuals’ blade-drive service.
- 5
Test the 3-second blade stop with the grass bag
The manuals ask you to check the blade-brake-clutch operation before each use or daily: the blades should stop within 3 seconds of releasing the blade-control bar. To check it with the grass bag, remove the rear-discharge plug and install the empty grass bag. Start the engine and engage the blades; the bag should begin to inflate, showing that the blades are turning. While watching the bag, release the blade-control bar. Then shut off the engine and wait for all moving parts to stop.
If the bag does not deflate within 3 seconds of releasing the blade-control bar, the manuals say the blade-stop system may be deteriorating and, if ignored, could result in an unsafe operating condition. Have the machine inspected and serviced by an Authorized Service Dealer. - 6
Or test the blade stop with a newspaper ball
Move the machine onto a paved surface in a non-windy area and set all 4 wheels to the 89 mm (3-1/2 inch) cutting height. Crumple a half sheet of newspaper into a ball small enough to go under the housing, about 76 mm (3 inches) across, and place it about 13 cm (5 inches) in front of the machine. Start the engine and engage the blades. Release the blade-control bar and count out 3 seconds; on the count of 3, push the machine quickly forward over the newspaper. Shut off the engine, wait for all moving parts to stop, and check the ball at the front of the machine. If the ball did not go under the machine, the manuals say to repeat the test from placing the ball.
If the newspaper is unravelled or shredded, the blades did not stop properly, which the manuals say could result in an unsafe operating condition. Contact an Authorized Service Dealer.
Belt replacement, belt diagram, blade engagement and transmission
Belt replacement: none of the seven manuals gives a procedure, an interval, a wear limit or symptoms for replacing the blade-drive belt, and none prints a belt size or part number. Their maintenance schedule has no belt-replacement row. What they do give is the 50-hour service and tension check above. All seven say that whenever you need service or genuine Toro parts, you should contact an Authorized Service Dealer or Toro Customer Service with the model and serial numbers of your machine ready.
Where the blade belt is: when we read them on 17 November 2026, Toro’s parts listings for the TimeMaster 30 linked an operator’s manual for each serial range. Across the 21199, the 21199HD and the 21200 they linked seven English manuals between them, and the blade-drive service in steps 2 to 4 above is printed the same, word for word apart from figure numbers, in all seven. The manuals call the belt the blade-drive belt. You reach it by removing the blade-drive system cover, and the manuals’ drawing labels a belt-tension spring, an adjusting bolt, an adjusting nut, the blade-drive belt, a wall and the gap you check.
Belt diagram: the manuals describe no belt routing in words. The belt appears in the drawing that goes with the tension check, labelled as listed above. Toro’s parts listings also carry assembly drawings; on the five listings read for this guide on 17 November 2026, their captions included Engine and Belt Assembly, Spindle and Belt Assembly, and Belt, Spindle and Blade Assembly.
Blade engagement belt and cable: the manuals do not use the words blade engagement belt. You engage the blades with the blade-control bar. When you start the engine, the blades do not turn; pull the blade-control-bar lock back to the bar, slowly pull the bar back to the handle, and hold it against the handle. Release the bar to disengage the blades, which should stop within 3 seconds. The only cable procedure the manuals give is the self-propel cable adjustment below. Otherwise they say that assembling and unfolding the handle improperly can damage the cables, and that if a cable is damaged you should contact an Authorized Service Dealer.
Transmission: the word does not appear in any of the seven manuals. They call it the self-propel drive, and cover it with the operating notes and the one adjustment in the self-propel section below. They mention no belt in the self-propel drive.
Belt service interval and the 3-second blade stop
Every 50 hours: service the blade-drive system. All seven manuals give this interval, and none gives another for the blade-drive system.
Before each use or daily: check the blade-brake-clutch operation. Under the same heading the manuals say to check that the blades stop within 3 seconds of releasing the blade-control bar. The two checks in the steps above, with the grass bag or a newspaper ball, are both printed in all seven.
The manuals word the blade stop two ways. Their operating section says that when you release the blade-control bar, “the blades should stop within 3 seconds”. Their safety section says that when you release it, “the engine should shut off and the blade should stop within 3 seconds”. We quote both and do not describe how the system works; the manuals do not describe the blade-brake-clutch either.
The same belt cover comes off in one other procedure. On the electric-start model, the battery-replacement steps include removing the belt cover, referring back to step 1 of the blade-drive service. Six manuals print this; 134599, whose cover names only the 21199HD, has no battery-replacement section.
Transmission: the self-propel drive and its cable adjustment
Using it, in all seven manuals: walk with your hands gripping the upper handle and your elbows at your sides, and the machine keeps pace with you. You can self-propel the machine with the blades engaged or disengaged. Use the traction-assist handle when you need more control than the self-propel drive alone gives.
Adjusting it, in all seven: whenever you install a new self-propel cable, or if the self-propel drive is out of adjustment, loosen the cable adjustment by turning it counterclockwise. Adjust the tension on the cable by pulling it back or pushing it forward and holding that position: push the cable toward the engine to increase the traction, or pull it away from the engine to decrease it. Then turn the adjustment clockwise to tighten it.
Where the manuals differ: 126842, 128680, 134599 and 139284 have you turn an adjustment knob and end with “Tighten the knob firmly by hand.” Their cover lines start at 21199 and 21200 serial 400000000 (126842), 21199 and 21200 serial 402082000 (128680), 21199HD serial 400000000 (134599), and 21199 serial 403600000, 21199HD serial 404314000 and 21200 serial 403600000 (139284). Those four also list a Traction Adjustment decal repeating the same three steps.
171808, 172235 and 185882 have you turn an adjustment nut, end with “Tighten the nut firmly with a socket or wrench.”, and head the section For Self-Propel-Drive Models Only. Their cover lines start at 21199 serial 404320000, 21199HD 404314000 and 21200 404320000 (171808); 21199 serial 405600000, 21199HD 404314000 and 21200 405700000 (172235); and 21199 serial 407700000, 21199HD 407000000 and 21200 407800000 (185882). The overview drawing in 171808 still labels the part an adjustment knob, although its procedure says nut. Use the manual whose cover line covers your model and serial number.
Blade belt part numbers: what the manuals and listings show
The seven manuals contain no parts list and print no belt part number. The only part-style numbers they print are decal numbers.
The accessory list on every TimeMaster 30 parts listing, as read on 16 November 2026, names oils, fuel products, the 20122P blade kit and a few other accessories, and none of them is a belt. That is a statement about the accessory list only. The listing pages also carry the assembly drawings named above, and the parts list for each drawing loads only when the drawing is opened. We have not read those lists, so we cannot tell you from them which belt number applies to your serial range.
When read on 17 November 2026, the listing for the 21199, serial 405600000 to 407699999, also linked a PDF parts catalog, form 3427-367, whose cover names the 21199 from serial 404320000. It prints belts under its Spindle and Belt Assembly and Engine and Belt Assembly drawings. It does not say which of them the operator’s manuals mean by the blade-drive belt, and we have not yet checked those numbers against Toro’s own part pages, so we do not print them here. Other listings link other catalogs, which we have not opened.
The two drive belts this site lists are 22 inch belts, fitted here to the 20334 and the 20339 from Toro’s listings for those models. No Toro page we hold ties either of them to the TimeMaster 30, so we do not suggest them for it.
The manuals ask for genuine parts: “use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty.” To get the right belt for your machine, give an Authorized Service Dealer or Toro Customer Service your model and serial numbers.
What the TimeMaster 30 manuals do not give
No belt-tension force or deflection, and no torque for the adjusting bolt, the adjusting nut or the cover bolts. The tension setting is the paper-slide feel in step 3.
No belt size, length, width or type, and no belt routing in words.
No description of how the blade-brake-clutch works, and no adjustment for the blade-control or brake side of the system. For a blade stop slower than 3 seconds, the manuals send you to an Authorized Service Dealer, and we do the same.
Engine service beyond what the manuals print is left to the engine’s own manual, which the manuals refer you to for additional maintenance procedures.
Related
Machines this covers
Related
Parts this guide mentions
Provenance
Sources
Last verified against these sources on November 17, 2026.
- 1
TimeMaster® 30in Lawn Mower Operator’s Manual — models 21199 and 21200, serial 400000000 and up
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 400000000 and Up”, “Model No. 21200-Serial No. 400000000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). Its maintenance schedule has no daily oil-level row; it prints the oil-level check procedure in its Operation section. It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment knob, tightened firmly by hand, and it lists a Traction Adjustment decal.
- 2
TimeMaster® 30in Lawn Mower Operator’s Manual — models 21199 and 21200, serial 402082000 and up
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 402082000 and Up”, “Model No. 21200-Serial No. 402082000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment knob, tightened firmly by hand, and it lists a Traction Adjustment decal.
- 3
TimeMaster® 30in Lawn Mower Operator’s Manual — model 21199HD, serial 400000000 and up
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199HD-Serial No. 400000000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily. Its schedule has no battery-charging rows. It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment knob, tightened firmly by hand, and it lists a Traction Adjustment decal.
- 4
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 403600000 and Up”, “Model No. 21199HD-Serial No. 404314000 and Up”, “Model No. 21200-Serial No. 403600000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment knob, tightened firmly by hand, and it lists a Traction Adjustment decal.
- 5
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 404320000 and Up”, “Model No. 21199HD-Serial No. 404314000 and Up”, “Model No. 21200-Serial No. 404320000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment nut, tightened firmly with a socket or wrench, although its overview drawing labels the part an adjustment knob.
- 6
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 405600000 and Up”, “Model No. 21199HD-Serial No. 404314000 and Up”, “Model No. 21200-Serial No. 405700000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz), with a footnote that residual oil stays in the crankcase after draining and the entire capacity should not be poured in; SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb); spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment nut, tightened firmly with a socket or wrench.
- 7
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 407700000 and Up”, “Model No. 21199HD-Serial No. 407000000 and Up”, “Model No. 21200-Serial No. 407800000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz), with a footnote that residual oil stays in the crankcase after draining and the entire capacity should not be poured in; SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb); spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine after each use; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment nut, tightened firmly with a socket or wrench.
- 8
Parts — 30in TimeMaster Lawn Mower, model 21199, serial range 400000000–402081999
The Toro Company · Primary source · Accessed November 16, 2026
As read on 17 August 2026: Earliest of the four ranges we opened. Lists 130-8149 (BRIGGS MAINT KIT - TM 17 & NEWER) and 20122P (15.4 Inch Hi-Lift Replacement Blade Kit (TimeMaster)). The range selector names ten further ranges for this model number. Opened again on 16 November 2026: 130-8149 and 117-0066 are no longer named on it. Read again on 16 November 2026: the accessory list named 10 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461.
- 9
Parts — 30in TimeMaster, model 21199, serial range 405600000–407699999
The Toro Company · Primary source · Accessed November 16, 2026
As read on 21 August 2026: Toro’s official parts listing for this model and serial range, reached from the serial-range selector its own page carries. Of the parts this site holds, its accessory list names 20120P, and does not name 130-8149, 130-8146, 20122P. The page carries further items this site holds no record for. Opened again on 16 November 2026: 20120P and 117-0066 are no longer named on it. Read again on 16 November 2026: the accessory list named 10 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461.
- 10
The Toro Company · Primary source · Accessed November 16, 2026
As read on 22 August 2026: Lists blade kit 20120P, the 15.4 Inch Atomic Blade, and the obsolete engine oil 117-0066. Toro’s own page title names this machine the Home Depot Rental TimeMaster, which is how it differs from the 21199. Opened again on 16 November 2026: 20120P and 117-0066 are no longer named on it. Read again on 16 November 2026: the accessory list named 11 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461, 59165.
- 11
The Toro Company · Primary source · Accessed November 16, 2026
As read on 22 August 2026: Lists blade kit 20120P, the 15.4 Inch Atomic Blade, and the obsolete engine oil 117-0066. Toro’s own page title names this machine the Home Depot Rental TimeMaster, which is how it differs from the 21199. Opened again on 16 November 2026: 20120P and 117-0066 are no longer named on it. Read again on 16 November 2026: the accessory list named 11 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461, 59165.
- 12
Parts — 30in TimeMaster Electric Start, model 21200, serial range 414514169–999999999
The Toro Company · Primary source · Accessed November 16, 2026
As read on 20 August 2026: The latest published range. Still no engine maintenance kit, and blade 20122P is listed. Read again on 16 November 2026: the accessory list named 10 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461.
