maintenance
Toro TimeMaster 30 oil capacity, torque specs and schedule
Short answer
All seven operator’s manuals Toro links for the TimeMaster 30 (21199, 21199HD and 21200) give an engine oil capacity of 0.53 L (18 fl oz) of SAE 30 or SAE 10W-30 detergent oil, API SJ or higher, a blade-bolt torque of 82 N∙m (60 ft-lb) and a spark-plug torque of 20 N∙m (15 ft-lb). Change the oil after the first 5 hours, then every 50 hours and yearly.
- Published
- Last verified
This guide is compiled from the manufacturer’s own documentation, cited below. We have not performed this procedure ourselves and do not claim to have.
Before you start
What you need
- A torque wrench
- A block of wood or a board to hold each blade steady
- A clean cloth
- A 0.25 mm (0.010 inch) feeler gauge, or a piece of paper or a note card
- Gloves and eye protection
- A hand fuel pump, if the fuel tank is not empty when you need to tip the machine
Procedure
Step by step
- 1
Prepare the machine before any maintenance
Shut off the engine, remove the ignition key if the machine has one, and wait for all moving parts to stop. Then disconnect the wire from the spark plug, and connect it again only when the work is finished. Wear gloves and eye protection. Before tipping the machine to change the oil or the blades, let the fuel tank run dry through normal use; if you must tip it sooner, remove the fuel with a hand fuel pump. The manuals say to always tip the machine onto its side with the dipstick down.
Tipping the machine may cause fuel to leak, and fuel is flammable and explosive. Run the engine dry or remove the fuel with a hand pump; never siphon it. - 2
Check the engine-oil level
With the machine on a level surface, remove the dipstick by turning its cap counterclockwise and pulling it out. Wipe it with a clean cloth, insert it into the oil-fill tube, remove it again and read the level. If it is low, pour in a small amount of SAE 30 or SAE 10W-30 detergent oil, wait 3 minutes and read it again, repeating until the level is correct. If it is too high, drain the excess. Manual 126842 prints these steps under Checking the Engine-Oil Level; the other six show that check as a drawing and print the same dipstick steps inside the oil-change procedure.
If the oil level is too low or too high and you run the engine, you may damage the engine. - 3
Change the engine oil
Run the engine a few minutes first: warm oil flows better and carries more contaminants. Move the machine to a level surface, prepare it as in step 1, and remove the dipstick. Tip the machine onto its side, so that the air filter is up, and drain the used oil out of the oil-fill tube. Return the machine to the operating position and pour in about 3/4 of the engine’s 0.53 L (18 fl oz) capacity. Wait 3 minutes for the oil to settle, then check the dipstick as in step 2, adding small amounts and waiting 3 minutes each time until the level is correct, or draining any excess. Install the dipstick securely and recycle the used oil.
- 4
Service the air filter
Loosen the fastener and remove the air-filter cover, then remove and inspect the filter. Replace it if it is damaged or wet with oil or fuel. If it is only dirty, tap it on a hard surface several times, or blow the debris outward from the inside of the filter with compressed air at less than 207 kPa (30 psi). Do not brush or blow dirt from the outside, which forces dirt into the fibers. Clean the filter body and cover with a damp rag, keeping dirt away from the air opening, then install the filter on its base and screw the cover’s fastener down securely.
- 5
Service the blade-drive system
Remove the blade-drive system cover and brush or blow out debris from inside the shield and around all the parts. Hold a 0.25 mm (0.010 inch) feeler gauge, a piece of paper or a note card against the wall and slide it down behind the belt-tension spring. If there is a visible gap between the gauge and the spring, tighten the adjusting bolt and nut until the paper barely slides freely in and out of the gap. Install the cover again.
Do not overtighten the adjusting bolt. The manuals warn that this could damage the blade-drive belt. - 6
Remove and install the blades at 82 N∙m (60 ft-lb)
Lock the handle in the vertical position and tip the machine onto its side, dipstick down, until the upper handle rests on the ground. Hold each blade steady with a block of wood and turn its bolt counterclockwise to remove it, then inspect the pins on the blade drivers for wear and damage. To install, fit the first blade horizontal with all its mounting hardware and tighten the bolt with your fingers. The curved ends of the blades point toward the housing; the raised areas on each blade driver nest in the recesses of its spindle, and the pins on the other side go through the holes in the blade. Steady the blade with a board and torque the bolt clockwise to 82 N∙m (60 ft-lb). Turn the installed blade 1/4 turn until it is vertical, install the second blade the same way, and torque it. The two blades should form an inverted T. Turn them by hand a full 360° to make sure they do not touch; if they do, they are not mounted correctly, so refit them until they no longer touch.
The manuals say you need a torque wrench for this, and to contact an Authorized Service Dealer if you do not have one or are uncomfortable doing it. Wear gloves. Use only genuine Toro replacement blades, and never straighten a bent blade or weld a broken or cracked one. - 7
Inspect the spark plug and torque it to 20 N∙m (15 ft-lb)
The manuals give the spark-plug torque in the procedure for taking the machine out of storage. Remove the spark plug and spin the engine rapidly with the starter to blow excess oil from the cylinder. Inspect the plug and replace it if it is dirty, worn or cracked, referring to the engine owner’s manual. Install it and tighten it to 20 N∙m (15 ft-lb). Check the oil level and fill the tank with fresh fuel, and connect the wire to the spark plug last.
The specifications, and which manuals state them
Toro’s parts listings for the TimeMaster 30 link an operator’s manual for each serial range. Across the three machines, the 21199, the 21199HD and the 21200, they link seven English manuals between them, and the listings start at serial 400000000. Every value in this section is printed in all seven, so it applies to every serial range those listings cover.
Engine oil capacity: 0.53 L (18 fl oz). Oil: SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher. When refilling after a drain, the manuals say to pour about 3/4 of that capacity first and bring it up to the dipstick mark in small amounts, waiting 3 minutes each time.
Blade-bolt torque: 82 N∙m (60 ft-lb), turning the bolt clockwise with a torque wrench while a board holds the blade steady.
Spark-plug torque: 20 N∙m (15 ft-lb).
Blade-drive belt-tension check: a 0.25 mm (0.010 inch) feeler gauge, or a piece of paper or a note card, slid down behind the belt-tension spring.
Air filter: clean it by tapping it on a hard surface, or by blowing from the inside outward with compressed air at less than 207 kPa (30 psi).
Bent blade: measure from a level surface to the cutting edges at the two points the manuals show, turn the blades so the opposite ends are at those points, and measure again. If the dimensions differ by more than 3 mm (1/8 inch), the blade is bent and must be replaced.
Blade stop: when you release the blade-control bar, the blades should stop within 3 seconds. If they do not, the manuals say to stop using the machine and contact an Authorized Service Dealer.
The maintenance schedule
After the first 5 hours: change the engine oil.
Before each use or daily: check the engine-oil level and add oil as needed (six of the seven manuals; see the differences below), check the blade-brake-clutch operation, check the air filter and clean or replace it if necessary, and check the cutting blades.
Cleaning under the machine: six manuals list it before each use or daily, and manual 185882 lists it after each use.
Every 25 hours: charge the battery for 24 hours, on the electric-start model only. Toro’s product page names the 21200 as the TimeMaster Electric Start.
Every 50 hours: clean the air filter, more often in dusty conditions; change the engine oil; and service the blade-drive system.
Every 200 hours: replace the air filter, more often in dusty conditions.
Yearly: service the air filter, change the engine oil, and service the blades.
Yearly or before storage: charge the battery (electric-start model only) and empty the fuel tank. For storage, the manuals also say to add about 30 ml (1 fl oz) of motor oil through the spark-plug hole and pull the starter rope slowly several times to spread it through the cylinder.
All seven also refer you to the engine’s own manual for further maintenance.
Where the seven manuals differ
The specifications above are the same in all seven. The differences are in the schedule and the notes around it, and each manual’s cover line gives the serial numbers it starts from.
Cleaning under the machine: “Before each use or daily” in 126842, 128680, 134599, 139284, 171808 and 172235; “After each use” in 185882, whose cover reads 21199 from serial 407700000, 21199HD from 407000000 and 21200 from 407800000.
Daily oil check: manual 126842, whose cover reads 21199 and 21200 from serial 400000000, does not list a daily oil-level check in its maintenance schedule. It does print the oil-level check procedure, and the other six list the check before each use or daily.
Refilling after a drain: 172235 and 185882 add a footnote to the 0.53 L (18 fl oz) capacity saying oil stays in the crankcase after draining, so you should not pour in the full capacity. All seven tell you to start with about 3/4 of it.
Blade bolt: 126842, 128680, 134599, 139284 and 171808 add that a bolt torqued to 82 N∙m (60 ft-lb) is very tight, that you should put your weight behind the wrench, and that it is very difficult to overtighten. 172235 and 185882 give the same torque without that note.
Battery: 134599, whose cover names only the 21199HD, carries no battery-charging rows in its schedule. The other six list them for the electric-start model only.
What the manuals leave to the engine manufacturer
None of the seven manuals gives a spark-plug type or a spark-plug gap. They say to inspect the plug and replace it if it is dirty, worn or cracked, and to refer to the engine owner’s manual. We have not filled that in, and you should take it from the engine owner’s manual.
The manuals say an engine owner’s manual is enclosed with the machine and that replacements may be ordered through the engine manufacturer. They do not name the engine’s maker. Toro’s product pages for the 21199 and the 21200 state a Briggs & Stratton 223 cc OHV engine; those pages do not say which serial ranges that applies to.
Toro oil and blades listed for these machines
Every serial-range parts listing Toro publishes for the 21199, 21199HD and 21200, as read on 16 November 2026, names these engine oils among its accessories: 38903 and 38916 (both SAE 30) and 138-6053 (Toro Full Synthetic 10W-30). Those match the two viscosities the manuals specify. Toro’s page for 138-6053 is headed “OIL-30/10W-30 SYNTHETIC CK4 [QT]”; none of the three oil pages states the SJ-or-higher classification the manuals ask for, so check the label.
The same listings name 20122P, the 15.4 Inch Hi-Lift Replacement Blade Kit (TimeMaster), for every serial range. The manuals ask for genuine Toro replacement blades; whichever you fit, the bolt torque is 82 N∙m (60 ft-lb).
Related
Machines this covers
Related
Parts this guide mentions
Provenance
Sources
Last verified against these sources on November 17, 2026.
- 1
OIL-30/10W-30 SYNTHETIC CK4 [QT] (Part # 138-6053), served at /product/117-0066
The Toro Company · Primary source · Accessed September 5, 2026
Requesting the 117-0066 product URL serves the page for 138-6053 under the line “Replaces Product 117-0066”, which is Toro stating the oil supersession directly rather than this site inferring it from which number sits against which serial range. Re-read 31 August 2026 and unchanged, and again 5 September 2026. Internal designation OIL-30/10W-30 SYNTHETIC CK4 [QT]. One bullet frames the oil for zero-turn riding mowers (TimeCutter MX, Titan, Titan MX) while the overview calls it the choice for any outdoor power equipment; the page names no walk-behind model. It does state a capacity — the title reads “(32 oz.)” and the first bullet repeats “10W-30 engine oil (32 oz.)” — corrected 5 September 2026 from an earlier reading that missed it.
- 2
TimeMaster® 30in Lawn Mower Operator’s Manual — models 21199 and 21200, serial 400000000 and up
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 400000000 and Up”, “Model No. 21200-Serial No. 400000000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). Its maintenance schedule has no daily oil-level row; it prints the oil-level check procedure in its Operation section. It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment knob, tightened firmly by hand, and it lists a Traction Adjustment decal.
- 3
TimeMaster® 30in Lawn Mower Operator’s Manual — models 21199 and 21200, serial 402082000 and up
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 402082000 and Up”, “Model No. 21200-Serial No. 402082000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment knob, tightened firmly by hand, and it lists a Traction Adjustment decal.
- 4
TimeMaster® 30in Lawn Mower Operator’s Manual — model 21199HD, serial 400000000 and up
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199HD-Serial No. 400000000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily. Its schedule has no battery-charging rows. It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment knob, tightened firmly by hand, and it lists a Traction Adjustment decal.
- 5
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 403600000 and Up”, “Model No. 21199HD-Serial No. 404314000 and Up”, “Model No. 21200-Serial No. 403600000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment knob, tightened firmly by hand, and it lists a Traction Adjustment decal.
- 6
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 404320000 and Up”, “Model No. 21199HD-Serial No. 404314000 and Up”, “Model No. 21200-Serial No. 404320000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz); SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb), with the note that the bolt is very tight and very difficult to overtighten; spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment nut, tightened firmly with a socket or wrench, although its overview drawing labels the part an adjustment knob.
- 7
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 405600000 and Up”, “Model No. 21199HD-Serial No. 404314000 and Up”, “Model No. 21200-Serial No. 405700000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz), with a footnote that residual oil stays in the crankcase after draining and the entire capacity should not be poured in; SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb); spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine before each use or daily; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment nut, tightened firmly with a socket or wrench.
- 8
The Toro Company · Primary source · Accessed November 17, 2026
Read on 17 November 2026. Coverage line: “Model No. 21199-Serial No. 407700000 and Up”, “Model No. 21199HD-Serial No. 407000000 and Up”, “Model No. 21200-Serial No. 407800000 and Up”. This site takes from it: engine oil capacity 0.53 L (18 fl oz), with a footnote that residual oil stays in the crankcase after draining and the entire capacity should not be poured in; SAE 30 or SAE 10W-30 detergent oil, API service classification SJ or higher; refill with about 3/4 of the capacity, then in small amounts with 3-minute waits; blade-bolt torque 82 N∙m (60 ft-lb); spark-plug torque 20 N∙m (15 ft-lb); blade-drive check with a 0.25 mm (0.010 inch) feeler gauge; air-filter cleaning with compressed air at less than 207 kPa (30 psi); bent blade above 3 mm (1/8 inch); blades stop within 3 seconds; about 30 ml (1 fl oz) of motor oil through the spark-plug hole for storage; and the schedule: oil change after the first 5 hours, every 50 hours and yearly; oil level checked before each use or daily; air filter checked daily, cleaned every 50 hours, replaced every 200 hours, serviced yearly; blade-drive system every 50 hours; blades checked daily and serviced yearly; cleaning under the machine after each use; battery charged every 25 hours and yearly or before storage (electric-start model only). It gives no spark-plug type or gap and refers to the engine owner’s manual. For the blade-drive belt guide (17 November 2026): the blade-drive service procedure (remove the cover, clear debris, slide the gauge behind the belt-tension spring, tighten the adjusting bolt and nut until the paper barely slides freely, do not overtighten); blade engagement with the blade-control bar; the blade-brake-clutch check before each use or daily; the grass-bag and newspaper blade-stop tests (all 4 wheels at 89 mm (3-1/2 inch), a ball about 76 mm (3 inches) across placed about 13 cm (5 inches) in front); the self-propel cable adjustment; and its Maintenance Safety, tamper, handle-and-cable, genuine-parts and service-contact lines. Its self-propel adjustment uses an adjustment nut, tightened firmly with a socket or wrench.
- 9
Parts — 30in TimeMaster Lawn Mower, model 21199, serial range 400000000–402081999
The Toro Company · Primary source · Accessed November 16, 2026
As read on 17 August 2026: Earliest of the four ranges we opened. Lists 130-8149 (BRIGGS MAINT KIT - TM 17 & NEWER) and 20122P (15.4 Inch Hi-Lift Replacement Blade Kit (TimeMaster)). The range selector names ten further ranges for this model number. Opened again on 16 November 2026: 130-8149 and 117-0066 are no longer named on it. Read again on 16 November 2026: the accessory list named 10 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461.
- 10
Parts — 30in TimeMaster Lawn Mower, model 21199, serial range 414709996–999999999
The Toro Company · Primary source · Accessed November 16, 2026
As read on 17 August 2026: The latest published range. Still no maintenance kit. Blade 20122P is listed again, and 20120P is not — so across the four ranges we opened the blade number does not move in one direction. Read again on 16 November 2026: the accessory list named 10 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461.
- 11
Parts — 30in TimeMaster Electric Start, model 21200, serial range 400000000–402081999
The Toro Company · Primary source · Accessed November 16, 2026
As read on 20 August 2026: Lists 130-8149 (BRIGGS MAINT KIT - TM 17 & NEWER) and 20122P (15.4 Inch Hi-Lift Replacement Blade Kit (TimeMaster)), plus 490-7461 and 130-2393. Opened again on 16 November 2026: 130-8149 and 117-0066 are no longer named on it. Read again on 16 November 2026: the accessory list named 10 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461.
- 12
Parts — 30in TimeMaster Electric Start, model 21200, serial range 414514169–999999999
The Toro Company · Primary source · Accessed November 16, 2026
As read on 20 August 2026: The latest published range. Still no engine maintenance kit, and blade 20122P is listed. Read again on 16 November 2026: the accessory list named 10 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461.
- 13
The Toro Company · Primary source · Accessed November 16, 2026
As read on 22 August 2026: Lists blade kit 20120P, the 15.4 Inch Atomic Blade, and the obsolete engine oil 117-0066. Toro’s own page title names this machine the Home Depot Rental TimeMaster, which is how it differs from the 21199. Opened again on 16 November 2026: 20120P, 117-0066 and 20601 are no longer named on it. Read again on 16 November 2026: the accessory list named 11 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461, 59165.
- 14
The Toro Company · Primary source · Accessed November 16, 2026
As read on 22 August 2026: Lists blade kit 20122P, the 15.4 Inch Hi-Lift Replacement Blade Kit, and engine oil 138-6053 in place of 117-0066. Toro’s own page title names this machine the Home Depot Rental TimeMaster, which is how it differs from the 21199. Read again on 16 November 2026: the accessory list named 11 items, among them 130-2393, 131-6572, 138-6053, 20122P, 20602, 38903, 38916, 490-7461, 59165.
- 15
30 in. TimeMaster w/ Personal Pace Gas Lawn Mower — model 21199
The Toro Company · Primary source · Accessed August 17, 2026
Product specification page. States "10.00 ft-lb Gross Torque Briggs & Stratton 223 cc OHV", a 30 in / 76 cm cutting width, "13 Gauge Steel" deck, "Personal Pace® Rear Wheel Drive Traction Assist", and 2 blades.
- 16
30 in. TimeMaster Electric Start w/ Personal Pace Gas Lawn Mower — model 21200
The Toro Company · Primary source · Accessed August 17, 2026
Product specification page. States a Briggs & Stratton 223 cc OHV engine, a 30 in / 76 cm cutting width, "13 Gauge Steel" deck and "Personal Pace® Rear Wheel Drive Traction Assist". The serial selector lists eleven ranges.
